On the mechanism of marine fouling-prevention performance of oil-containing silicone elastomers.

For many decades, silicone elastomers with oil incorporated have served as fouling-release coating for marine applications. In a comprehensive study involving a series of laboratory-based marine fouling assays and extensive global field studies of up to 2-year duration, we compare polydimethylsiloxane (PDMS) coatings of the same composition loaded with oil via two different methods. One method used a traditional, one-pot pre-cure oil addition approach (o-PDMS) and another method used a newer post-cure infusion approach (i-PDMS). The latter displays a substantial improvement in biofouling prevention performance that exceeds established commercial silicone-based fouling-release coating standards. We interpret the differences in performance between one-pot and infused PDMS by developing a mechanistic model based on the Flory-Rehner theory of swollen polymer networks. Using this model, we propose that the chemical potential of the incorporated oil is a key consideration for the design of future fouling-release coatings, as the improved performance is driven by the formation and stabilization of an anti-adhesion oil overlayer on the polymer surface.

Sewage sludge ash-based mortar as construction material: Mechanical studies, macrofouling, and marine toxicity.

Incinerated sewage sludge ash is tested here as a cement and aggregate substitute in mortar blocks. It can be used at various percentages to reduce the overall cost of production and promote ash recycling. The compressive strength of the cast blocks was tested at 28 days to determine the optimal combination of ball milled ash (replacing cement) and sewage sludge ash (replacing sand). This was compared with a control block made of cement and sand only. The cast blocks with the optimal ash formulation were tested for their flexural strength and other properties such as surface functional groups, constituent phases and porosity. The control and ash mortars exhibited similar properties. A potential application of these blocks is to use them as part of seawalls. These blocks were thus suspended in the sea for 6 months. Marine organism attachment was observed over time in both control and ash mortar blocks. There was no significant difference between the mortars after 6 months. The mortar blocks were also subjected to leaching tests (NEN-7345). The leachates did not exhibit toxicity to microalgae. In contrast, mild toxicity was observed in the sea urchin embryo development assay. Overall, the study suggests that sewage sludge ash is a potential material to be used for seawall construction as it has the desirable mechanical properties. However, there remain some residual marine toxicity concerns that need to be further addressed.

A comparative investigation of toxicity of three polymer nanoparticles on acorn barnacle (Amphibalanus amphitrite).

Pollution from plastic waste is increasingly prevalent in the environment and beginning to generate significant adverse impact on the health of living organisms. In this study, we investigate the toxicity of polymer nanoparticles exposed to Acorn Barnacle (Amphibalanus amphitrite) nauplii, as an animal model. Highly stable aqueous dispersion of luminescent nanoparticles from three common polymers: polymethylmethacrylate (PMMA), polystyrene (PS), and polyvinylchloride (PVC), were prepared via nanoprecipitation and fully characterised. Exposure studies of these polymer particles to freshly spawned barnacle nauplii were performed within a concentration range from 1 to 25 mg/L under laboratory-controlled conditions. The exposure to PMMA and PS nanoparticles did not show detrimental toxicity and did not cause sufficient mortality to compute a LC50 value. However, PVC nanoparticles were significantly toxic with a mortality rate of up to 99% at 25 mg/L, and the calculated LC50 value for PVC nanoparticles was 7.66 ± 0.03 mg/L, 95% CI. Interestingly, PVC nanoparticle aggregates were observed to adhere to the naupliar carapace and appendages at higher concentrations and could not be easily removed by washings. To explore the possibility of chemical toxicity of polymer nanoparticles, analysis of the polymer powders which was used to prepare the nanoparticles was conducted. The presence of low molecular weight oligomers such as dimers, trimers and tetramers were observed in all polymer samples. The chemical nature and concentration of such compounds are likely responsible for the observed toxicity to the barnacle nauplii. Overall, our study shows that care should be exercised in generalising the findings of exposure studies performed using one type of plastic particles, as the use of different plastic particles may elicit different responses inside a living organism.

Spirobranchus bakau sp. nov. from Singapore: yet another species of S. kraussii-complex (Polychaeta: Serpulidae).

The intertidal serpulid polychaete Spirobranchus kraussii was originally described from South Africa and has since been reported in numerous sub (tropical) localities around the world. Recently, however, S. kraussii was uncovered as a complex of morphologically similar and geographically restricted species, raising the need to revise S. cf. kraussii populations. We formally describe S. cf. kraussii from Singapore mangroves as Spirobranchus bakau sp. nov. based on morphological and molecular data. Despite their morphological similarities, Maximum Likelihood and Bayesian Inference analyses of 18S and Cyt b DNA sequence data confirm that S. bakau sp. nov. is genetically distinct from S. kraussii and other known species in the complex. Both analyses recovered S. bakau sp. nov. as part of a strongly supported clade (96% bootstrap, 1 posterior probability), comprising S. sinuspersicus, S. kraussii and S. cf. kraussii from Australia and Hawaii. Additionally, paratypes of S. kraussii var. manilensis, described from Manila Bay in the Philippines, were examined and elevated to the full species S. manilensis. Finally, we tested the hypothesis that fertilisation and embryonic development of S. bakau sp. nov. can occur under the wide range of salinities (19.630.9 psu) and temperatures (2531C) reported in the Johor Strait. Fertilisation success of ≥70% was achieved across a temperature range of 2532C and a salinity range of 2032 psu. Embryonic development, however, had a narrower salinity tolerance range of 2732 psu. Clarifying the taxonomic status of S. cf. kraussii populations reported from localities elsewhere in Singapore and Southeast Asia will be useful in establishing the geographical distribution of S. bakau sp. nov. and other members of the S. kraussii-complex.

Ascidians collected during the 2013 Singapore Strait International Marine Biodiversity Workshop.

During the 2013 Singapore Strait International Marine Biodiversity Workshop, hundreds of ascidians were collected along with numerous other marine phyla. Collections were made intertidally as well as subtidally by snorkel, SCUBA, trawling and dredging. While many ascidian specimens remain unidentified, 14 aplousobranchs, nine phlebobranchs and 17 stolidobranchs have been identified; a surprising 50% of these comprise 20 new records for Singapore. An additional new record of the phlebobranch Perophora namei collected from the same area in 2014 and 2015 is included here. Of the 21 new records, Aplidium cf. grisiatum, Distaplia regina, Euherdmania cf. digitata, Cnemidocarpa irene, Monandrocarpa monotestis and Polyandrocarpa rollandi are also first records for the entire South China Sea region.

Incinerated Sewage Sludge Bottom Ash- Chemical processing, Leaching patterns and Toxicity testing.

Sewage sludge bottom ash, which is the major fraction obtained from the incineration of sewage sludge was treated with various organic and inorganic acids for heavy metal removal, along with a comparative phosphate treatment for heavy metal fixation. Malonic acid, an organic acid, was found to remove heavy metals better as compared to nitric acid, a strong inorganic acid. The acid treated samples were further examined for heavy metal leaching, followed by marine toxicity/abnormality testing of the leachates, where acid treated and phosphate treated ash leachate displayed higher (with malonic acid proving to be most toxic) and similar toxicity profiles as compared to raw ash leachate respectively. Raw ash was tested for its leaching patterns at different liquid/solid ratios(L/S = 5 and 10), salinities and time points (24, 48 and 72 h), where the leaching was found to saturate at L/S = 5 and at 24 h with varied salinity effecting the leaching insignificantly. When raw ash was benchmarked against concrete sand for marine toxicity, a material commonly used for land reclamation, acute toxicity patterns were found to be mostly similar except in case of the sea urchin embryonic assay, where toxicity was detected, indicating the sensitivity of the assay to residual levels of heavy metals. The raw ash was also tested against human cell lines where it displayed size and dose-dependent toxicity. To enable the use of ash for environment applications such as coastal reclamation, appropriate treatments are required to minimize leaching of potential harmful contaminants and this study demonstrates the importance of post-treatment of ash on its subsequent toxicity to organisms.

Removal of larvae of two marine invasive bivalves, Mytilopsis sallei (Récluz, 1849) and Mytella strigata (Hanley, 1843), by water treatment processes.

The uptake and discharge of bivalve larvae through ballast water operations is a highly viable mechanism for transfer of shellfish. In this paper, we investigate the effects of common water treatment processes on the planktotrophic larvae of the two invasive species of shellfish, Mytilopsis sallei and Mytella strigata. The study found that common water treatment processes used in many ballast water treatment systems were effective for the removal of bivalve larvae, although later stages of larval forms required more effort to remove.

Evaluation of sewage sludge incineration ash as a potential land reclamation material.

This study evaluated the potential of utilising sewage sludge incineration ash as a land reclamation material. Toxicity assessment of the leachate of the ash was carried out for both terrestrial and marine organisms. Both the fruit fly Drosophila melanogaster and barnacle Amphibalanus amphitrite showed that both bottom and fly ash leached at liquid-to-solid (L/S) ratio 5 did not substantially affect viabilities. The leachate carried out at L/S 10 was compared to the European Waste Acceptance Criteria and the sewage sludge ashes could be classified as non-hazardous waste. The geotechnical properties of the sewage sludge ash were studied and compared to sand, a conventional land reclamation material, for further evaluation of its potential as a land reclamation material. It was found from direct shear test that both bottom and fly ashes displayed similar and comparable shear strength to that of typical compacted sandy soil based on the range of internal friction angle obtained. However, the consolidation profile of bottom ash was significantly different from sand, while that of fly ash was more similar to sand. Our study showed that the sewage sludge ash has the potential to be used as a land reclamation material.

Effect of Variations in Micropatterns and Surface Modulus on Marine Fouling of Engineering Polymers.

We report on the marine fouling and fouling release effects caused by variations of surface mechanical properties and microtopography of engineering polymers. Polymeric materials were covered with hierarchical micromolded topographical patterns inspired by the shell of the marine decapod crab Myomenippe hardwickii. These micropatterned surfaces were deployed in field static immersion tests. PDMS, polyurethane, and PMMA surfaces with higher elastic modulus and hardness were found to accumulate more fouling and exhibited poor fouling release properties. The results indicate interplay between surface mechanical properties and microtopography on antifouling performance.

Comparison of laboratory and field testing performance evaluations of siloxane-polyurethane fouling-release marine coatings.

A series of eight novel siloxane-polyurethane fouling-release (FR) coatings were assessed for their FR performance in both the laboratory and in the field. Laboratory analysis included adhesion assessments of bacteria, microalgae, macroalgal spores, adult barnacles and pseudobarnacles using high-throughput screening techniques, while field evaluations were conducted in accordance with standardized testing methods at three different ocean testing sites over the course of six-months exposure. The data collected were subjected to statistical analysis in order to identify potential correlations. In general, there was good agreement between the laboratory screening assays and the field assessments, with both regimes clearly distinguishing the siloxane-polyurethane compositions comprising monofunctional poly(dimethyl siloxane) (PDMS) (m-PDMS) as possessing superior, broad-spectrum FR properties compared to those prepared with difunctional PDMS (d-PDMS). Of the seven laboratory screening techniques, the Cellulophaga lytica biofilm retraction and reattached barnacle (Amphibalanus amphitrite) adhesion assays were shown to be the most predictive of broad-spectrum field performance.

Measuring protein isoelectric points by AFM-based force spectroscopy using trace amounts of sample.

Protein charge at various pH and isoelectric point (pI) values is important in understanding protein function. However, often only trace amounts of unknown proteins are available and pI measurements cannot be obtained using conventional methods. Here, we show a method based on the atomic force microscope (AFM) to determine pI using minute quantities of proteins. The protein of interest is immobilized on AFM colloidal probes and the adhesion force of the protein is measured against a positively and a negatively charged substrate made by layer-by-layer deposition of polyelectrolytes. From the AFM force-distance curves, pI values with an estimated accuracy of ±0.25 were obtained for bovine serum albumin, myoglobin, fibrinogen and ribonuclease A over a range of 4.7-9.8. Using this method, we show that the pI of the 'footprint' of the temporary adhesive proteins secreted by the barnacle cyprid larvae of Amphibalanus amphitrite is in the range 9.6-9.7.

Antifouling coatings based on covalently cross-linked agarose film via thermal azide-alkyne cycloaddition.

Coatings based on thin films of agarose-poly(ethylene glycol) (Agr-PEG) cross-linked systems are developed as environmentally-friendly and fouling-resistant marine coatings. The Agr-PEG cross-linked systems were prepared via thermal azide-alkyne cycloaddition (AAC) using azido-functionalized Agr (AgrAz) and activated alkynyl-containing poly(2-propiolamidoethyl methacrylate-co-poly(ethylene glycol)methyl ether methacrylate) P(PEMA-co-PEGMEMA) random copolymers as the precursors. The Agr-PEG cross-linked systems were further deposited onto a SS surface, pre-functionalized with an alkynyl-containing biomimetic anchor, dopamine propiolamide, to form a thin film after thermal treatment. The thin film-coated SS surfaces can effectively reduce the adhesion of marine algae and the settlement of barnacle cyprids. Upon covalent cross-linking, the covalently cross-linked Agr-PEG films coated SS surfaces exhibit good stability in flowing artificial seawater, and enhanced resistance to the settlement of barnacle cyprids, in comparison to that of the surfaces coated with physically cross-linked AgrAz films.

Antibacterial, electrospun nanofibers of novel poly(sulfobetaine) and poly(sulfabetaine)s.

Polymers capable of forming hydration layers have gained increasing attention due to their ability to form environmentally friendly antifouling surfaces. Zwitterionic polymers are an important class of materials under this category. However, the effectiveness of many zwitterionic polymers for long-term applications is compromised because of their solubility in sea water, poor hydrolytic stability and deteriorating mechanical integrity upon wetting. This study reports on the preparation and characterization of electrospun fibers derived from novel polysulfobetaine and polysulfabetaines (PSBs) composed of polyvinylbenzyl backbones. The morphology of the electrospun nanofibers was elucidated with the help of a scanning electron microscope. Hydration studies were conducted in deionized water and artificial sea water. Antifouling performance of the electrospun nanofibers was evaluated by studying the adhesion and growth of bacteria in natural, and filtered sea water. Terminal restriction fragment length polymorphism (TRFLP) fingerprinting was performed to determine the nature of the bacterial community attached to the electrospun fibers. Some of the PSBs prevented bacterial growth without showing any biocidal nature. Thus the findings of this study are potentially relevant for current trends seeking environmentally friendly antifouling solutions.

Tea stains-inspired initiator primer for surface grafting of antifouling and antimicrobial polymer brush coatings.

Inspired by tea stains, plant polyphenolic tannic acid (TA) was beneficially employed as the primer anchor for functional polymer brushes. The brominated TA (TABr) initiator primer was synthesized by partial modification of TA with alkyl bromide functionalities. TABr with trihydroxyphenyl moieties can readily anchor on a wide range of substrates, including metal, metal oxide, polymer, glass, and silicon. Concomitantly, the alkyl bromide terminals serve as initiation sites for atom transfer radical polymerization (ATRP). Cationic [2-(methacryloyloxy)ethyl]trimethylammonium chloride (META) and zwitterionic 2-methacryloyloxyethyl phosphorylcholine (MPC) and N-(3-sulfopropyl)-N-(methacryloxyethyl)-N,N-dimethylammonium betaine (SBMA) were graft-polymerized from the TABr-anchored stainless steel (SS) surface. The cationic polymer brushes on the modified surfaces are bactericidal, while the zwitterionic coatings exhibit resistance against bacterial adhesion. In addition, microalgal attachment (microfouling) and barnacle cyprid settlement (macrofouling) on the functional polymer-grafted surfaces were significantly reduced, in comparison to the pristine SS surface. Thus, the bifunctional TABr initiator primer provides a unique surface anchor for the preparation of functional polymer brushes for inhibiting both microfouling and macrofouling.

Polyion multilayers with precise surface charge control for antifouling.

We report on a molecular fabrication approach to precisely control surface ζ potentials of polymeric thin layers constructed by electrostatic layer-by-layer (LbL) assembly methods. The protocol established allows us to achieve surface isoelectric points (IEP) in the pH range of 6-10. Poly(acrylic acid) (PAA, a weak polyanion) and poly(diallyldimethylammonium chloride) (PDADMAC, a strong polycation) were chosen to build up the bulk films. The weak polycation polyethylenimine (PEI) was applied as a top layer. A unique feature of this approach is that the chemical composition of the top layer is not affected by the manipulation of the ζ potential of the films. Surface charge tuning is achieved by controlling the degree of ionization of the weak polyelectrolytes at various pH values and subsequent manipulation of the amount of polyelectrolyte deposited in the penultimate and last layers, respectively. Following assembly and characterization, the films were used as candidates for antifouling surfaces. The fouling behavior of barnacle cyprids and bacteria on the LbL films with similar hydrophilicity and roughness but different surface charge densities were studied. We found that more cyprids of Amphibalanus amphitrite settled on the negatively charged LbL film compared to the neutral or positively charged LbL film. In bacterial adhesion tests employing Pseudomonas, Escherichia coli, and Staphylococcus aureus, more bacteria were observed on the positively charged LbL film compared with the neutral and negatively charged LbL films, possibly as a result of the negative potential of the bacterial cell wall. The procedures proposed allow one to adjust surface isoelectric points of LbL architectures to achieve optimal antifouling performance of a given material taking into account specific pH values of the environment and the character of the fouler.

Barnacle larvae exploring surfaces with variable hydrophilicity: influence of morphology and adhesion of "footprint" proteins by AFM.

Interaction forces of adhesive proteins employed by cyprid larvae of Amphibalanus amphitrite for temporary attachment during surface exploration in marine fouling were studied by AFM force spectroscopy using chemically modified, reactive colloidal probes. The proteins were covalently attached to the surfaces of the probes by incubation in the protein deposits (footprints) left behind at the surface by the cyprids. This covalent coupling enabled robust and reproducible probing of adhesion of the attachment proteins to model surfaces with variable hydrophilicity. Three model monolayer surfaces were designed and prepared that exhibited different wettabilities derived from variations in the monolayer chemical composition. The morphology and size of cyprid protein deposits was imaged by AFM. The deposits showed larger area of spreading on more hydrophobic surfaces, whereas the overall volume of the secreted proteins exhibited no significant variation. Notable difference in adhesion forces was found among the surfaces by force spectroscopy, with substantially higher values measured on the hydrophobic surface (21 ± 2 nN) than that measured on the more hydrophilic surface (7.2 ± 1 nN). The same surfaces were also tested in laboratory essays. Rather surprisingly, no significant differences were found in values of fractional cyprid settlement among the surfaces studied, indicating that variations of surface wettability and adhesion strength of settlement proteins may be insufficient to explain settlement trends.

Sulfobetaine-based polymer brushes in marine environment: is there an effect of the polymerizable group on the antifouling performance?

Three different zwitterionic polymer brush coatings for marine biofouling control were prepared by surface-initiated atom transfer radical polymerization (ATRP) of sulfobetaine-based monomers including methacrylamide (SBMAm), vinylbenzene (SBVB) and vinylimidazolium (SBVI). None of these brush systems have been assessed regarding marine antifouling performance. Antifouling tests performed indicate that surfaces featuring these three brush systems substantially reduce the adhesion of the marine microalgae, Amphora coffeaeformis, and the settlement of cyprid larvae of the barnacle, Amphibalanus amphitrite, in a similar way, displaying comparable performance. Thus, it appears that the chemical structure of the polymerizable group has no substantial influence on marine antifouling performance.

Effect of ultrasound on cyprid footprint and juvenile barnacle adhesion on a fouling release material.

In our earlier studies, we have demonstrated that low and high intensity ultrasound can prevent barnacle cyprid settlement. In this study, we found that ultrasound treatment reduced the adhesion of newly metamorphosed barnacles up to 2 days' old. This was observed in the reduction of adhesion strength of the newly settled barnacles from ultrasound treated cyprids on silicone substrate compared to the adhesion strength of barnacles metamorphosed from cyprids not exposed to ultrasound. Atomic force microscopy (AFM) was used to analyze the effect of ultrasound on barnacle cyprid footprints (FPs), which are protein adhesives secreted when the larvae explore surfaces. The ultrasound treated cyprids were found to secrete less FPs, which appeared to spread a larger area than those generated by untreated cyprids. The evidence from this study suggests that ultrasound treatment results in a reduced cyprid settlement and footprint secretion, and may affect the subsequent recruitment of barnacles onto fouling release surfaces by reducing the ability of early settlement stage of barnacles (up to 2 days' old) from firmly adhering to the substrates. Ultrasound therefore can be used in combination with fouling release coatings to offer a more efficient antifouling strategy.

Multilayers of fluorinated amphiphilic polyions for marine fouling prevention.

Sequential layer-by-layer (LbL) deposition of polyelectrolytes followed by chemical cross-linking was investigated as a method to fabricate functional amphiphilic surfaces for marine biofouling prevention applications. A novel polyanion, grafted with amphiphilic perfluoroalkyl polyethylene glycol (fPEG) side chains, was synthesized and subsequently used to introduce amphiphilic character to the LbL film. The structure of the polyanion was confirmed by FTIR and NMR. Amphiphilicity of the film assembly was demonstrated by both water and hexadecane static contact angles. XPS studies of the cross-linked and annealed amphiphilic LbL films revealed the increased concentration of fPEG content at the film interface. In antifouling assays, the amphiphilic LbL films effectively prevented the adhesion of the marine bacterium Pseudomonas (NCIMB 2021).